学习就是要系统，而不是学习零碎的知识，就像现在的小学课本一样，学生每天忙忙碌碌，看似学习了很多内容，实际并未学习到很多核心的内容。
对于学习数控机床电气知识，我整理了两本电子书，如果你想系统学习，建议你下载学习下。
今天我们来聊一聊PLC中的英文注释问题，这个注释呢说白了就是对PLC程序的一种解释，这些注释，可以编写中文、可以编写英文、或者缩写，并未有明确的规范要求。
对于一些PLC软件，可以编写中文，那么，编写程序的人就会编写中文注释，那么你阅读起程序来就比较直观，对于一些软件不能够编写中文，那么就可能会使用一些英文或者英文缩写来注释。
对于同一个程序编写者，大部分注释是相同的，比如主轴松刀，会写SP UNCLAMP 等等。看习惯了，或者记住了常用的注释，那么阅读起PLC程序是不是很方便。
广告：扫描领取网络赚钱小副业，按照教程操作，即可在网络上持续赚钱。
为了方便学习这些英文注释以及缩写词，我整理了一些中英文注释表，希望对于学习PLC的人有所帮助。
| 注释 | 别名 | |
| CHIP CONVEYOR RUN | 排屑器运行 | CCRN.R |
| FLOOD COOLANT MOTOR | 溢流冷却电机 | CLFM.R |
| TSC COOLANT MOTOR | TSC冷却电机 | TSC.R |
| BED SHOWER COOLANT MOTOR | 喷淋冷却泵 | BCO.R |
| COOLANT GUN MOTOR | 冷却枪泵 | CGUN.R |
| HYDRAULIC UNIT MOTOR | 液压泵 | HYD.R |
| LUBRICATION UNIT MOTOR | 润滑泵 | LUBM.R |
| OIL MIST COLLECTOR MOTOR | 油雾收集电机 | OMC.R |
| 4TH-AXIS CLAMP & UNCLAMP | 4轴夹紧松开 | 4TH.R |
| DOOR OPEN CONDITION | 自动门打开 | DIC.R |
| MACHINE READY | 机床准备就绪 | MCR.R |
| SERVO MOTOR BREAK RELEASE | 伺服电机制动释放 | SMBR.R |
| NC READY | NC就绪 | NCR.R |
| WORK LIGHT ON RELAY | 工作灯 | WL.R |
| FLUSHING/SHOWER COOLANT MOTOR | 冲洗喷淋冷却电机 | FCO.R |
| WORKPIECE MEASURE ON | 工件测量 | WPM.R |
| TOOL MEASURE SENSOR ON | 刀具测量传感器打开 | TMS.R |
| TOOL MEASURE SENSOR LATCH MODE | 刀具测量传器闭锁模式 | TMLM.R |
| EXTERNAL M91 RELAY ON | 外部M91继电器打开 | EM91.R |
| EXTERNAL M92 RELAY ON | 外部M92继电器打开 | EM92.R |
| EXTERNAL M93 RELAY ON | 外部M93继电器打开 | EM93.R |
| EXTERNAL M94 RELAY ON | 外部M94继电器打开 | EM94.R |
| PATROL LIGHT RED | 红灯 | PLR.R |
| PATROL LIGHT GREEN | 绿灯 | PLG.R |
| PATROL LIGHT YELLOW | 黄灯 | PLY.R |
| FIXTURE 1 CLAMP | 夹具1夹紧 | F1C.R |
| FXITURE 1 UNCLAMP | 夹具1松开 | F1UC.R |
| FIXTURE 2 CLAMP | 夹具2夹紧 | F2C.R |
| FIXTURE 2 UNCLAMP | 夹具2松开 | F2UC.R |
| FIXTURE 3 CLAMP | 夹具3夹紧 | F3C.R |
| FIXTURE 3 UNCLAMP | 夹具3松开 | F3UC.R |
| SPINDLE TOOL UNCLAMP | 主轴刀具松开 | STUL.L |
| MPG LAMP | MPG灯 | MPG.L |
| AIR SEAL CHECK | 气密检测 | ASC.R |
| AIR BLOWING RELAY | 吹气继电器 | . |
| TOOL MEASURE AIR BLOW | 刀具测量吹气 | TMAB.R |
| COLLET AIR | 夹头空气 | CAIR.R |
| SPINDLE TOOL UNCLAMP | 主轴刀具松开 | STUN.R |
| TOOL MAGAZINE CW ON | 刀库正转 | TMF.R |
| TOOL MAGAZINE CCW ON | 刀库反转 | TMR.R |
| TOOL CHANGER + DIRECTION | 换刀臂正向 | TCF.R |
| TOOL CHANGER - DIRECTION | 换刀臂反向 | TCR.R |
| ATC MOTOR POWER ON | ATC电机 | AMP.R |
| MAGAZINE TOOL POT DOWN | 刀袋倒下 | TPD.R |
| MAGAZINE TOOL POT UP | 刀袋缩回 | TPU.R |
| AUTO DOOR OPEN | 自动门打开 | DOP.R |
| AUTO DOOR CLOSE | 自动门关闭 | DOC.R |
| AUTO DOOR SOFT START & SLOW DOWN | 自动门软启动和减速 | DSS.R |
| CYCLE START LAMP | 循环启动灯 | STL.L |
| CYCLE STOP LAMP | 循环停止灯 | SPL.L |
| FIXTURE CLAMP/UNCLAMP LAMP | 夹具夹紧松开灯 | FCLP.L |
| LURICATION ALARM LAMP | LURICATION报警灯 | LUBA.L |
| MACHINE READY LAMP | 机床就绪灯 | MRDL.L |
| M02/M03 STATE LAMP | M02/M03状态灯 | 32L.L |
| TAPE MODE LAMP | 磁带模式灯 | TAPEL.L |
| MEMORY MODE LAMP | 记忆模式灯 | MEML.L |
| MDI MODE LAMP | MDI模式灯 | MDIL.L |
| REFERENCE RETURN MODE LAMP | 回零模式灯 | REFL.L |
| JOG MODE LAMP | 点动模式灯 | JOGL.L |
| HANDLE MODE LAMP | 手轮模式灯 | HANL.L |
| ALARM STATE LAMP | 报警状态灯 | ALML.L |
| SPINDLE ORIENTATION LAMP | 主轴定向灯 | SPOL.L |
| 4TH AXIS CLAMP LAMP | 4轴夹紧灯 | 4CL.L |
| 5TH AXIS CLAMP LAMP | 5轴夹紧灯 | 5CL.L |
| X AXIS REFERENCE RETURN LAMP | X轴原位灯 | XRRL.L |
| Y AXIS REFERENCE RETURN LAMP | Y轴原位灯 | YRRL.L |
| Z AXIS REFERENCE RETURN LAMP | Z轴原位灯 | ZRRL.L |
| 4 AXIS REFERENCE RETURN LAMP | 4轴原位灯 | 4RRL.L |
| 5 AXIS REFERENCE RETURN LAMP | 5轴原位灯 | 5RRL.L |
| AUTO DOOR CLOSE LAMP | 自动门关闭灯 | ADCL.L |
| OIL MIST COLLECTOR LAMP | 油雾收集器灯 | OMCL.L |
| SINGLE BLOCK LAMP | 单步灯 | SBKL.L |
| OPTIONAL BLOCK SKIP LAMP | 可选块跳过灯 | BDTL.L |
| OPTIONAL STOP LAMP | 操作停止灯 | BDTL.L |
| DRY RUN LAMP | 同步运行灯 | DRNL.L |
| PROGRAM RESTART LAMP | 程序重启灯 | PRSL.L |
| AUTO POWER OFF LAMP | 自动断电灯 | APOL.L |
| ALL AXIS MACHINE LOCK LAMP | 所有轴锁定灯 | AALL.L |
| Z AXIS MACHINE LOCK LAMP | Z轴锁定灯 | ZALL.L |
| MST LOCK LAMPY247 | MST锁定灯 | MSTLL.L |
| RAPID F0 OVERRIDE LAMP | 快速0超控灯 | RF0L.L |
| RAPID 25% OVERRIDE LAMP | 快速25超控灯 | R25L.L |
| RAPID 50% OVERRIDE LAMP | 快速50超控灯 | R50L.L |
| RAPID 100% OVERRIDE LAMP | 快速100超控灯 | R100L.L |
| FLOOD COOLANT ON LAMP | 溢流冷却开启灯 | FCOL.L |
| COOLANT OFF LAMP | 冷却关闭灯 | COFFL.L |
| TSC MANUAL OPERATION LAMP | TSC手动操作灯 | TSCL.L |
| SHOWER COOLANT MANUAL OP LAMP | 喷淋手动操作灯 | SHWL.L |
| AIR BLOW MANUAL OPERATION LAMP | 吹气手动操作灯 | ABL.L |
| COOLANT GUN MANUAL OP LAMP | 水枪手动操作灯 | CGL.L |
| AUTO DOOR OPEN LAMP | 自动门打开灯 | ADOP.L |
| CHIP CONVEYOR RUN LAMP | 排屑器运行灯 | CCRL.L |
| WORK LIGHT LAMP | 工作灯 | WLL.L |
| MAGAZINE ROTATION MODE LAMP | 刀库旋转模式灯 | MRL.L |
| CHANGER ARM ROTATION MODE LAMP | 换刀臂模式灯 | CARL.L |
| CW LAMP | 正转灯 | CWL.L |
| CCW LAMP | 反转灯 | CCWL.L |
| SPINDLE MANUAL ON LAMP | 主轴手动运行灯 | SMOL.L |
| SPINDLE STOP LAMP | 主轴停止灯 | SSPL.L |
| SPINDLE START LAMP | 主轴启动灯 | SSTL.L |
| FIXTURE 4 CLAMP | 4轴夹紧 | F4C.R |
| FIXTURE 4 UNCLAMP | 4轴松开 | F4UC.R |
| 5TH-AXIS CLAMP & UNCLAMP | 5轴夹紧松开 | 5TH.R |
| AUTO POWER OFF | 自动电源关闭 | APO.R |
| TOOL COUNTER 1 | 刀具计数1 | CNT1.R |
| TOOL COUNTER 2 | 刀具计数2 | CNT2.R |
| TOOL COUNTER 3 | 刀具计数3 | CNT3.R |
| TOOL COUNTER 4 | 刀具计数4 | CNT4.R |
| TOOL COUNTER 5 | 刀具计数5 | CNT5.R |
| DAILY WORKPIECE COUNTER | 日工件计数器 | CNTD.R |
| TOTAL WORKPIECE COUNTER | 工件总数计数器 | CNTT.R |
| OIL COOLING UNIT RUN | 油冷机运行 | OCON.R |
| PLC S/W, TAP RETRACT | 测头缩回 | |
| PLC S/W, TOOL LENGTH MAN MEASURE | 刀具长度人工测量 | |
| (B)TOOL DATA, CORDINATE PROTECT | （B)刀具数据保护 | KEY1 |
| (B)PARAMETER, VARIABLES PROTECT | （B)参数、变量保护 | KEY2 |
| (B)PROGRAM PROTECT | （B)程序保护 | KEY3 |
| 4 AXIS DETACH | 4轴断开 | DTCH4 |
| (B)4 AXIS SERVO OFF | （B)4轴伺服关闭 | SVF4 |
| X AXIS MIRROR IMAGE | X轴镜像 | MI1 |
| Y AXIS MIRROR IMAGE | Y轴镜像 | MI2 |
| Z AXIS MIRROR IMAGE | Z轴镜像 | MI3 |
| 4 AXIS MIRROR IMAGE | 4轴镜像 | MI4 |
| 5 AXIS MIRROR IMAGE | 5轴镜像 | MI5 |
| (B)+X AXIS INTERLOCK, AUTO | （B)X+联锁、自动 | |
| (B)+Y AXIS INTERLOCK, AUTO | （B)Y+联锁、自动 | |
| (B)+Z AXIS INTERLOCK, AUTO | （B)Z+联锁、自动 | |
| (B)+4 AXIS INTERLOCK, AUTO | （B)4+联锁、自动 | |
| (B)-X AXIS INTERLOCK, AUTO | （B)X-联锁、自动 | |
| (B)-Y AXIS INTERLOCK, AUTO | （B)Y-联锁、自动 | |
| (B)-Z AXIS INTERLOCK, AUTO | （B)Z-联锁、自动 | |
| (B)-4 AXIS INTERLOCK, AUTO | （B)4-联锁、自动 | |
| (B)+X AXIS INTERLOCK, MANUAL | （B)X+联锁、手动 | |
| (B)+Y AXIS INTERLOCK, MANUAL | （B)Y+联锁、手动 | |
| (B)+Z AXIS INTERLOCK, MANUAL | （B)Z+联锁、手动 | |
| (B)+4 AXIS INTERLOCK, MANUAL | （B)5+联锁、手动 | |
| (B)-X AXIS INTERLOCK, MANUAL | （B)X-联锁、手动 | |
| (B)-Y AXIS INTERLOCK, MANUAL | （B)Y-联锁、手动 | |
| (B)-Z AXIS INTERLOCK, MANUAL | （B)Z-联锁、手动 | |
| (B)-4 AXIS INTERLOCK, MANUAL | （B)5-联锁、手动 | |
| AUTO, MACHINE LOCK X AXIS | 自动、锁定轴X | AMLK1 |
| AUTO, MACHINE LOCK Y AXIS | 自动、锁定轴Y | AMLK2 |
| AUTO, MACHINE LOCK Z AXIS | 自动、锁定轴Z | AMLK3 |
| AUTO, MACHINE LOCK 4 AXIS | 自动、锁定轴4 | AMLK4 |
| AUTO, MACHINE LOCK 5 AXIS | 自动、锁定轴5 | AMLK5 |
| MANUAL, MACHINE LOCK X AXIS | 手动、锁定轴X | MMLK1 |
| MANUAL, MACHINE LOCK Y AXIS | 手动、锁定轴Y | MMLK2 |
| MANUAL, MACHINE LOCK Z AXIS | 手动、锁定轴Z | MMLK3 |
| MANUAL, MACHINE LOCK 4 AXIS | 手动、锁定轴4 | MMLK4 |
| MANUAL, MACHINE LOCK 5 AXIS | 手动、锁定轴5 | MMLK5 |
| JOG +X AXIS | 点动X+ | |
| JOG +Y AXIS | 点动Y+ | |
| JOG +Z AXIS | 点动Z+ | |
| JOG +4 AXIS | 点动4+ | |
| JOG +5 AXIS | 点动5+ | |
| JOG -X AXIS | 点动X- | |
| JOG -Y AXIS | 点动Y- | |
| JOG -Z AXIS | 点动Z- | |
| JOG -4 AXIS | 点动4- | |
| JOG -5 AXIS | 点动5- | |
| JOG MODE | 点动模式 | JOG |
| HANDLE MODE | 手轮模式 | HAN |
| REFERENCE RETURN MODE | 回零模式 | REF |
| MEMORY MODE | 记忆模式 | MEM |
| TAPE MODE | 磁带模式 | TAPE |
| MDI MODE | MDI模式 | MDI |
| CYCLE START | 循环启动 | ST |
| (B)FEED HOLD | （B)进给保持 | SP |
| SINGLE BLOCK | 单步 | SBK |
| DRY RUN | 试运行 | DRN |
| EXTERNAL NC RESET | 外部数控复位 | NRST2 |
| RESET & REWIND | 复位和倒带 | RRW |
| M,S,T FUNCTION FINISH | MST结束 | FIN |
| TOOL LENGTH MANUAL MEASURE ON | 手动测量刀具长度 | TLM |
| PROGRAM RESTART | 程序重启 | PRST |
| RAPID TRVERSE | 快速 | RT |
| PLC EMERGENCY STOP | PLC急停 | QEMG |
| OPTIONAL BLOCK SKIP 1 | 可选块跳过1 | BDT1 |
| OPTIONAL BLOCK SKIP 2 | 可选块跳过2 | BDT2 |
| OPTIONAL BLOCK SKIP 3 | 可选块跳过3 | BDT3 |
| OPTIONAL BLOCK SKIP 4 | 可选块跳过4 | BDT4 |
| OPTIONAL BLOCK SKIP 5 | 可选块跳过5 | BDT5 |
| OPTIONAL BLOCK SKIP 6 | 可选块跳过6 | BDT6 |
| OPTIONAL BLOCK SKIP 7 | 可选块跳过7 | BDT7 |
| OPTIONAL BLOCK SKIP 8 | 可选块跳过8 | BDT8 |
| OPTIONAL BLOCK SKIP 9 | 可选块跳过9 | BDT9 |
| HANDLE 1 AXIS SELECT 1 | 手轮1轴选1 | HS11 |
| HANDLE 1 AXIS SELECT 2 | 手轮1轴选2 | HS12 |
| HANDLE 1 AXIS SELECT 3 | 手轮1轴选3 | HS13 |
| HANDLE 1 ENABLE | 手轮1启用 | HS1S |
| OVERRIDE CANCEL | 超控取消 | OVC |
| AUX FUNCTION LOCK | 辅助功能锁 | AFL |
| TAP RETRACT ON | 点击收回 | TRV |
| FEEDRATE OVERRIDE 1 | 进给速率超控1 | FV1 |
| FEEDRATE OVERRIDE 2 | 进给速率超控2 | FV2 |
| FEEDRATE OVERRIDE 4 | 进给速率超控4 | FV4 |
| FEEDRATE OVERRIDE 8 | 进给速率超控8 | FV8 |
| FEEDRATE OVERRIDE 16 | 进给速率超控16 | FV16 |
| RAPID TRAVERSE OVERRIDE 1 | 快速移动超控1 | ROV1 |
| RAPID TRAVERSE OVERRIDE 2 | 快速移动超控2 | ROV2 |
| JOG FEEDRATE PLC SETTING METHOD | 点动进给速度PLC设定方法 | JVS |
| JOG FEEDRATE UNIT 1 | 点动进给单元1 | PCF1 |
| JOG FEEDRATE UNIT 2 | 点动进给单元2 | PCF2 |
| MPG OVERRIDE 1 | MPG超控1 | MP1 |
| MPG OVERRIDE 2 | MPG超控2 | MP2 |
| DATA COUNT VALID (TOOL LIFE) | 数据计数有效（刀具寿命） | TCEF |
| TOOL LIFE MANAGEMENT INPUT | 刀具寿命管理输入 | TCF1 |
| SPINDLE OVERRIDE SETTING CHANGE | 主轴超控设置更改 | SOSC |
| SPINDLE FORWARD ROTATION | 主轴正转 | CW |
| SPINDLE REVERSE ROTATION | 主轴反转 | CCW |
| SPINDLE ORIENTATION COMMAND | 主轴定向指令 |
| 注释 | 中文 | 别名 |
| LUBRICATION MANUAL START | 润滑手动启动 | LMS.M |
| LUBRICATION LEVEL CHECK | 润滑液位检查 | LUB.M |
| LUBRICATION PRESSURE CHECK | 润滑压力检查 | LPRS.M |
| CHIP CONVEYOR RUN CHECK | 排屑器运行检查 | CCRN.M |
| CHIP CONVEYOR RUN FAULT | 排屑器运行故障 | CCFT.M |
| INDUCTION & FAN MOTOR OVERLOAD | 感应和风扇电机过载 | IMOL.M |
| INDUCTION MOTOR OVERLOAD | 感应电机过载 | MOL.M |
| CIRCUIT PROTECTOR TRIP | 电路保护器跳闸 | TRIP.M |
| POWER SUPPLY POWER ON | 电源打开 | PMON.M |
| AIR PRESSURE CHECK | 气压检查 | APRS.M |
| 4TH-AXIS(AIR TYPE) PRESSURE CHK | 4轴气压检查 | 4PRS.M |
| TSC COOLANT FILTER PRESSURE CHK | TSC冷却液过滤器压力检查 | TSCP.M |
| COOLANT TANK LOW LEVEL CHECK | 冷却液箱低液位检查 | CTL.M |
| HYDRAULIC PRESSURE CHECK | 液压压力检查 | HYDP.M |
| OPERATION DOOR LOCK & CLOSE | 操作门打开和关闭 | MDIT.M |
| OPERATION DOOR CLOSE | 操作门关闭 | SDIC.M |
| EXTERNAL M-CODE FINISH | 外部M码完成 | EMF.M |
| WORKPIECE MEASURE ERROR | 工件测量错误 | WME.M |
| WORKPIECE MEASURE LOW BATTERY | 工件测量电池电量低 | WMLB.M |
| FIXTURE 1 PRESSURE CHECK | 夹具1压力检查 | F1PS.M |
| FIXTURE 2 PRESSURE CHECK | 夹具2压力检查 | F2PS.M |
| FIXTURE 3 PRESSURE CHECK | 夹具3压力检查 | F3PS.M |
| FIXTURE 4 PRESSURE CHECK | 夹具4压力检查 | F4PS.M |
| FIXTURE AIR SEAL CHECK | 夹具气密检查 | FASC.M |
| OIL COOLING UNIT FAULT | 油冷机故障 | OCFT.M |
| SPARE | 备用 | X19 |
| SPARE | 备用 | X1A |
| (B)4TH-AXIS REF.POINT | (B）4轴参考点 | DC4.M |
| SPARE | 备用 | X1C |
| 4TH-AXIS CLAMP SWITCH | 4轴夹紧按钮 | 4CC.M |
| 4TH-AXIS UNCLAMP SWITCH | 4轴松夹按钮 | 4UC.M |
| 4TH-AXIS DETECT | 4轴检测 | 4NG.M |
| SPINDLE TOOL UNCLAMP | 主轴刀具松夹 | STUN.M |
| SPINDLE TOOL CLAMP CHECK | 主轴刀具夹紧检查 | STC.M |
| 1ST TOOL POT DETECTION | 1号刀袋检查 | TPT1.M |
| TOOL POT COUNT | 刀袋数量 | TPCO.M |
| TOOL POT COUNT 2 | 刀袋数量2 | TPCO2.M |
| CHANGER ARM HOME POSITION | 换刀臂原位 | CAHP.M |
| CHANGER ARM HOME POSITION 2 | 换刀臂原位2 | CAH2.M |
| TOOL CLAMP COMMAND POSITION | 刀具夹紧指令位置 | CCMD.M |
| TOOL UNCLAMP COMMAND POSITION | 刀具松开指令位置 | UCMD.M |
| WAITING POT SPINDLE SIDE | 等待刀袋主轴侧 | WPSS.M |
| WAITING POT MAGAZINE SIDE | 等待刀袋刀库侧 | WPMS.M |
| AUTO DOOR OPEN CONFIRM | 自动门打开确认 | DOC.M |
| AUTO DOOR OPEN SLOW DOWN | 自动门打开减速 | DOS.M |
| AUTO DOOR CLOSE SLOW DOWN | 自动门关闭减速 | DCS.M |
| AUTO DOOR SAFETY EDGE | 自动门安全边沿 | DSE.M |
| EMERGENCY STOP SIGNAL | 急停信号 | EPS.M |
| TOOL COUNT LIFE END | 刀具计数寿命结束 | TCE.M |
| WORKPIECE COUNT LIFE END | 工件计数寿命结束 | WCE.M |
| HANDLE FEED X10 | 手轮进给X10 | MP12 |
| HANDLE FEED X100 | 手轮进给X100 | MP13 |
| HANDLE X AXIS SELECT | 手轮轴选X | HX1 |
| HANDLE Y AXIS SELECT | 手轮轴选Y | HY1 |
| HANDLE Z AXIS SELECT | 手轮轴选Z | HZ1 |
| HANDLE 4 AXIS SELECT | 手轮轴选4 | H41 |
| HANDLE 5 AXIS SELECT | 手轮轴选5 | H51 |
| SPARE | 备用 | X3F |
| CYCLE START | 循环启动 | ST.M |
| (B)CYCLE STOP | （B)循环停止 | SP.M |
| MANUAL FIXTURE UN/CLAMP | 夹具手动夹紧放松 | MFC.M |
| (B)MACHINE ALARM RESET | （B)机器报警复位 | MAR.M |
| MACHINE READY | 机器准备就绪 | MRD.M |
| PROGRAM PROTECT | 程序保护 | PP.M |
| TAPE MODE | 磁带模式 | TAPE.M |
| MEMORY MODE | 内存模式 | MEM.M |
| MDI MODE | MDI模式 | MDI.M |
| REFERENCE RETURN MODE | 回零模式 | REF.M |
| JOG MODE | 点动模式 | JOG.M |
| HANDLE MODE | 手轮模式 | HAN.M |
| JOG +X SELECT | 点动X+ | J+X.M |
| JOG -X SELECT | 点动X- | J-X.M |
| JOG +Y SELECT | 点动Y+ | J+Y.M |
| JOG -Y SELECT | 点动Y- | J-Y.M |
| JOG +Z SELECT | 点动Z+ | J+Z.M |
| JOG -Z SELECT | 点动Z- | J-Z.M |
| JOG +4 SELECT | 点动4+ | J+4.M |
| JOG -4 SELECT | 点动4- | J-4.M |
| JOG +5 SELECT | 点动5+ | J+5.M |
| MANUAL FIXTURE SELECT 2&JOG -5 | 点动5- | MFS2.M |
| JOG RAPID TRAVERSE | 点动快速移动 | JRP.M |
| SINGLE BLOCK | 单步 | SBK.M |
| OPTIONAL BLOCK SKIP | 可选块跳过 | BDT.M |
| OPTIONAL STOP | 可选块停止 | OPS.M |
| DRY RUN | 试运行 | DRN.M |
| PROGRAM RESTART | 程序重启 | PRS.M |
| AUTO POWER OFF | 自动电源关闭 | APO.M |
| MACHINE LOCK ALL AXES | 所有轴锁定 | MLKA.M |
| MACHINE LOCK Z AXIS | Z轴锁定 | MLKZ.M |
| MST LOCK | MST锁定 | MSTL.M |
| RAPID F0 OVERRIDE | 快速0 | RF0.M |
| RAPID 25% OVERRIDE | 快速25 | R25.M |
| RAPID 50% OVERRIDE | 快速50 | R50.M |
| RAPID 100% OVERRIDE | 快速100 | R100.M |
| FLOOD COOLANT MANUAL ON | 溢流冷却液手动打开 | FCO.M |
| COOLANT MANUAL OFF | 冷却液手动关闭 | COFF.M |
| TSC MANUAL OPERATION | TSC手动操作 | TSCM.M |
| SHOWER COOLANT MANUAL OPERATION | 冲洗冷却液手动操作 | SCM.M |
| AIR BLOW MANUAL OPERATION | 吹气手动操作 | ABM.M |
| COOLANT GUN MANUAL OPERATION | 冷却枪手动操作 | CGM.M |
| AUTO DOOR OPEN | 自动门打开 | ADOP.M |
| CHIP CONVEYOR ON | 排屑器工作 | CC.M |
| WORK LIGHT ON | 工作灯亮 | WL.M |
| MAGAZINE ROTATION SELECT | 刀库旋转选择 | MRS.M |
| CHANGER ARM ROTATION SELECT | 换刀臂旋转选择 | CAR.M |
| CW ROTAION | 正转 | CW.M |
| CCW ROTAION | 反转 | CCW.M |
| SPINDLE MANUAL ON | 主轴手动打开 | SMO.M |
| SPINDLE STOP | 主轴停止 | SSP.M |
| SPINDLE START | 主轴启动 | SST.M |
| MANUAL FIXTURE SELECT 1 | 手动夹具选择1 | MFS1.M |
| SPINDLE SPEED OVERRIDE 1 | 主轴速度超控1 | SPA.M |
| SPINDLE SPEED OVERRIDE 2 | 主轴速度超控2 | SPB.M |
| SPINDLE SPEED OVERRIDE 3 | 主轴速度超控3 | SPC.M |
| SPINDLE SPEED OVERRIDE 4 | 主轴速度超控4 | SPD.M |
| FEEDRATE OVERRIDE 1 | 进给速率超控1 | FV1.M |
| FEEDRATE OVERRIDE 2 | 进给速率超控2 | FV2.M |
| FEEDRATE OVERRIDE 3 | 进给速率超控3 | FV3.M |
| FEEDRATE OVERRIDE 4 | 进给速率超控4 | FV4.M |
| FEEDRATE OVERRIDE 5 | 进给速率超控5 | FV5.M |
| AUTO DOOR CLOSE | 自动门关闭 | ADCP.M |
| OIL MIST COLLECTOR ON | 油雾收集器打开 | OMC.M |
| 5TH AXIS DETECT | 5轴检测 | 5NG.M |
| NC RESET BUTTON | 数控复位按钮 | |
| PLC S/W, TAP RETRACT | TAP缩回 | |
| PLC S/W, TOOL LENGTH MAN MEASURE | 刀具长度人工测量 | |
| BATTERY WARNING | 电池警告 | BATWR |
| BATTERY ALARM | 电池警报 | BATAL |
| 4 AIXS SELECTED | 4轴选择 | AX4 |
| X AXIS + MOVING | X轴+ | MVP1 |
| Y AXIS + MOVING | Y轴+ | MVP2 |
| Z AXIS + MOVING | Z轴+ | MVP3 |
| 4 AXIS + MOVING | 4轴+ | MVP4 |
| 5 AXIS + MOVING | 5轴+ | MVP5 |
| X AXIS - MOVING | X轴- | MVM1 |
| Y AXIS - MOVING | Y轴- | MVM2 |
| Z AXIS - MOVING | Z轴- | MVM3 |
| 4 AXIS - MOVING | 4轴- | MVM4 |
| 5 AXIS - MOVING | 5轴- | MVM5 |
| X AXIS REFERENCE POINT POSITION | X轴参考点 | ZP11 |
| Y AXIS REFERENCE POINT POSITION | Y轴参考点 | ZP12 |
| Z AXIS REFERENCE POINT POSITION | Z轴参考点 | ZP13 |
| 4 AXIS REFERENCE POINT POSITION | 4轴参考点 | ZP14 |
| 5 AXIS REFERENCE POINT POSITION | 5轴参考点 | ZP15 |
| X AXIS 2ND REF. POINT POSTION | X轴第2参考点 | ZP21 |
| Y AXIS 2ND REF. POINT POSTION | Y轴第2参考点 | ZP22 |
| Z AXIS 2ND REF. POINT POSTION | Z轴第2参考点 | ZP23 |
| 4 AXIS 2ND REF. POINT POSTION | 4轴第2参考点 | ZP24 |
| 5 AXIS 2ND REF. POINT POSTION | 5轴第2参考点 | ZP25 |
| X AXIS REFERENCE ESTABLISHMENT | X轴基准建立 | XRE |
| Y AXIS REFERENCE ESTABLISHMENT | Y轴基准建立 | YRE |
| Z AXIS REFERENCE ESTABLISHMENT | Z轴基准建立 | ZRE |
| 4 AXIS REFERENCE ESTABLISHMENT | 4轴基准建立 | 4RE |
| 5 AXIS REFERENCE ESTABLISHMENT | 5轴基准建立 | 5RE |
| IN JOG MODE | 点动模式中 | JO |
| IN HANDLE MODE | 手轮模式中 | HO |
| IN REFERENCE RETURN MODE | 回零模式中 | ZRNO |
| IN MEMORY MODE | 内存模式中 | MEMO |
| IN TAPE MODE | 磁带模式中 | TO |
| IN MDI MODE | MDI模式中 | DO |
| NC READY | NC就绪 | MA |
| SERVO READY | 伺服就绪 | SA |
| AUTO RUNING STATE | 自动运行状态 | OP |
| CYCLE START | 循环启动 | STL |
| FEED HOLD | 循环保持 | SPL |
| NC RESET | NC复位 | RST |
| MOTION COMMAND COMPLETE | 动作指令完成 | DEN |
| ALL AXES IN-POSITION | 所有轴同一位置 | TIMP |
| IN RAPID TRAVERSE | 快速跳过 | RPN |
| IN CUTTING | 切割中 | CUT |
| IN TAPPING | 攻丝中 | TAP |
| IN THREAD CUTTING | 螺纹切削 | THRD |
| IN SYN | 同步中 | SYN |
| IN REFERENCE POINT RETURN | 参考点返回中 | ZRNN |
| TOOL LIFE IN MANAGEMENT STATUS | 刀具寿命处于管理状态 | TLFO |
| TOOL LIFE OVER SIGNAL | 刀具寿命到期 | |
| M00 PROGRAM STOP | M00程序停止 | M00 |
| MO1 OPTIONAL PROGRAM STOP | MO1可选程序停止 | M01 |
| M02 PROGRAM END | M02程序结束 | M02 |
| M30 PROG END & REWIND | M30程序结束和循环 | M30 |
| M FUNCTION STROBE | M功能选通 | MF |
| S FUNCTION STROBE | S功能选通 | SF |
| T FUNCTION STROBE | T功能选通 | TF |
| NC ALARM 1 | 数控报警1 | |
| NC ALARM 3 | 数控报警3 | |
| NC ALARM 4 | 数控报警4 | |
| TAPPING RETRACT ENABLE | 攻丝缩回启用 | |
| WORKPIECE COUNTER OVER | 工件计数结束 | PCNT |
| IN SYNCHRONIZED TAPPING | 同步攻丝中 | RTAP |
| SPINDLE SPEED DETECTED | 主轴速度检测 | VRO |
| SPINDLE ALARM | 主轴报警 | FLO |
| SPINDLE 0 SPEED | 主轴速度0 | ZSO |
| SPINDLE SPEED ARRIVAL | 主轴速度到达 | USO |
| SPINDLE ORIENTATION COMPLETED | 主轴定向完成 | |
| SPINDLE READY-ON | 主轴准备就绪 | SMA |
| SPINDLE CW RUNNING | 主轴正转 | |
| SPINDLE CCW RUNNING | 主轴反转 |
| 注释 | 中文 | 别名 |
| PROGRAM STOP | 程序停止 | |
| OPTIONAL STOP | 可选停止 | |
| PROGRAM END | 程序结束 | |
| SPINDLE ROTATION(C.W) | 主轴正转 | |
| SPINDLE ROTATION(C.C.W) | 主轴反转 | |
| SPINDLE STOP | 主轴停止 | |
| ATC TOOL CHANGE | 换刀 | |
| THROUGH THE SPINDLE COOLANT ON | 主轴中心出水 | |
| FLOOD COOLANT ON | 冷却启动 | |
| COOLANT OFF | 冷却关闭 | |
| 4TH-AXIS CLAMP | 4轴夹紧 | |
| 4TH-AXIS UNCLAMP | 4轴松开 | |
| SHOWER COOLANT ON | 喷淋开启 | |
| AIR BLOW ON | 吹气开启 | |
| AIR BLOW OFF | 吹气关闭 | |
| SPINDLE ORIENTATION | 主轴定向 | |
| CHIP CONVEYOR RUN | 排屑器开启 | |
| CHIP CONVEYOR STOP | 排屑器关闭 | |
| RIGID TAPPING MODE ON | 刚性攻丝模式开启 | |
| PROGRAM END (RESET & REWIND) | 程序结束 | |
| 5TH AXIS CLAMP | 5轴夹紧 | |
| 5TH AXIS UNCLAMP | 5轴松开 | |
| MACHINE FLUSHING COOLANT ON | 机器冲洗开 | |
| SPINDLE TOOL NO. SETTING | 主轴刀具编号设置 | |
| OVERRIDE CANCEL ON | 覆盖取消开启 | |
| OVERRIDE CANCEL OFF | 覆盖取消关闭 | |
| AUTO DOOR OPEN | 自动门打开 | |
| AUTO DOOR CLOSE | 自动门关闭 | |
| PARTS COUNT | 零件数量 | |
| REPEAT PROGRAM AFTER M02/30 | 重复程序 | |
| TOOL MEASUREMENT LATCH MODE ON | 刀具测量模式打开 | |
| WORK/TOOL MEASUREMENT SENSOR OFF | 工件/刀具测量模式关闭 | |
| WORKPIECE MEASUREMENT SENSOR ON | 工件测量模式打开 | |
| TOOL MEASUREMENT SENROR ON | 刀具测量模式打开 | |
| MIRROR IMAGE OFF | 镜像关闭 | |
| MIRROR IMAGE X-AXIS | X轴镜像 | |
| MIRROR IMAGE Y-AXIS | Y轴镜像 | |
| MIRROR IMAGE Z-AXIS | Z轴镜像 | |
| MIRROR IMAGE 4-AXIS | 4轴镜像 | |
| MIRROR IMAGE 5-AXIS | 5轴镜像 | |
| EXTERNAL M-CODE M91 | 外部M代码M91 | |
| EXTERNAL M-CODE M92 | 外部M代码M92 | |
| EXTERNAL M-CODE M93 | 外部M代码M93 | |
| EXTERNAL M-CODE M94 | 外部M代码M94 | |
| SUB PROGRAM CALL | 子程序调用 | |
| END OF SUB PROGRAM | 子程序结束 | |
| OIL MIST COLLECTER ON | 油雾收集器打开 | |
| OIL MIST COLLECTER OFF | 油雾收集器关闭 | |
| COLLET AIR BLOW ON | 夹头吹气打开 | |
| COLLET AIR BLOW OFF | 夹头吹气关闭 | |
| SPINDLE MULTI ORIENTATION | 主轴多向 | |
| TOOL MEASUREMENT AIR BLOW ON | 刀具测量吹气打开 | |
| TOOL MEASUREMENT AIR BLOW OFF | 刀具测量吹气关闭 | |
| FIXTURE 1 CLAMP | 夹具1夹紧 | |
| FIXTURE 1 UNCLAMP | 夹具1松开 | |
| FIXTURE 2 CLAMP | 夹具2夹紧 | |
| FIXTURE 2 UNCLAMP | 夹具2松开 | |
| FIXTURE 3 CLAMP | 夹具3夹紧 | |
| FIXTURE 3 UNCLAMP | 夹具3松开 | |
| FIXTURE 4 CLAMP | 夹具4夹紧 | |
| FIXTURE 4 UNCLAMP | 夹具4松开 | |
| AXIS MOVING VALID WHEN SP STOP | 主轴停止时轴移动有效 | |
| AXIS MOVING INVALID WHEN SP STOP | 主轴停止时轴移动无效 | |
| SUB PROGRAM CALL | 子程序调用 | |
| END OF SUB PROGRAM | 子程序结束 | |
| WAITING POT UP | 等待刀套抬起 | |
| WAITING POT DOWN | 等待刀套落下 | |
| == 0 == HIGH SPEED PROGRAM | 高速程序 | 0 |
| == 1 == OP PANEL SIGNAL | 操作面板信号 | 1 |
| == 2 == SPINDLE AREA | 主轴区域 | 2 |
| == 3 == ATC AREA | ATC区域 | 3 |
| == 4 == OTHER FUNCTION AREA | 其他功能区 | 4 |
| == 5 == OPTION AREA | 选项区域 | 5 |
| == 6 == MST SIGNAL | MST信号 | 6 |
| == 7 == ALARM AREA | 报警区域 | 7 |
| == 8 == WINDOWS READ & WRITE | 窗口读写 | 8 |
| == 9 == INITIAL AREA | 初始区域 | 9 |
| SP SPEED ARRIVAL INTERLOCK | 主轴速度到达连锁 | SARINT |
| SPINDLE STOP COMMAND | 主轴停止指令 | M05A |
| SPINDLE STAND-BY AUX | 主轴备用辅助 | SBYA |
| SPINDLE STAND-BY | 主轴备用 | SBY |
| SPINDLE FORWARD COMMAND | 主轴正转指令 | CW |
| SPINDLE REVERSE COMMAND | 主轴反转指令 | CCW |
| SPINDLE REVERSE MEMORY STATE | 主轴反向记忆状态 | SRM |
| SPINDLE FORWARD FLAG | 主轴正转标志 | SFF |
| SPINDLE FORWARD KEEP STATE | 主轴正转保持 | SFK |
| SPINDLE REVERSE FLAG | 主轴反转标志 | SRF |
| SPINDLE REVERSE KEEP STATE | 主轴反转保持 | SRK |
| SPINDLE M-CODE FINISH | 主轴M代码完成 | SPLFIN |
| M29 CODE FINISH | M29代码完成 | M29FIN |
| TAP RETRACTING | 攻丝回退 | TRE |
| SPINLDE ORIENTATION READY | 主轴定向就绪 | SOR |
| SPINDLE ORIENTATION COMMAND AUX | 主轴定向指令辅助 | SOCA |
| M19 CODE FINISH | M19代码完成 | M19FIN |
| TOOL NO. SEARCH ERROR | 刀具编号搜索错误 | |
| MAG ROTATION DIRECTION | 刀库旋转方向 | |
| TOOL TABLE CW ROTATION ERROR | 刀库正向旋转错误 | |
| TOOL TABLE CCW ROTATION ERROR | 刀库反向旋转错误 | |
| TOOL COUNTER AUX | 辅助刀具计数器 | |
| MAGAZINE ROTATION STOP | 刀库旋转停止 | |
| MAGAZINE POT COUNT CONDITION | 刀套计数条件 | |
| MAGAZINE MANUAL MODE | 刀库手动模式 | |
| ATC ARM MANUAL MODE | 刀臂手动模式 | |
| MAG MANUAL MODE SELECT PULSE | 刀库手动模式选择脉冲 | |
| MAG MANUAL MODE SELECT AUX | 刀库手动模式选择辅助 | |
| ARM MANUAL MODE SELECT PULSE | 刀臂手动模式选择脉冲 | |
| ARM MANUAL MODE SELECT AUX | 刀臂手动模式选择辅助 | |
| MAGAZINE AUTO ROTATION COMMAND | 刀库自动旋转指令 | |
| MAGAZINE MANUAL FORWARD | 刀库手动正转 | |
| MAGAZINE MANUAL REVERSE | 刀库手动反转 | |
| MAGAZINE MANUAL ROTATING | 刀库手动旋转 | |
| MAGAZINE MANUAL STOP FLAG | 刀库手动停止标志 | |
| TOOL NO. COUNT ERROR | 刀具编号计数错误 | |
| TOOL NO. SETTING OK | 刀具编号设置正常 | |
| TOOL NO. SEARCH AUX | 刀具编号搜索辅助 | TNSA |
| MAGAZINE ROTATION FLAG | 刀库旋转标志 | |
| TOOL NO. TRANSFER AUX | 刀具编号传输辅助 | TNTA |
| TOOL COUNTER DOWN PULSE | 刀具计数器下降脉冲 | |
| MAGAZINE ROTATION INITIAL POS. | 刀库旋转初始位置 | |
| TOOL COUNTER 2 MEMORY RESET | 刀具计数器2记忆复位 | |
| T-CODE COMMAND ERROR | T代码指令错误 | |
| T-CODE EQUAL SPINDLE TOOL NO. | T代码等于主轴刀具编号 | |
| T-CODE EQUAL WAITING TOOL NO. | T代码等于等待刀具编号 | |
| WAIT TOOL NO. "0" FOR BIG TOOL | 等待刀具号0表示大刀 | |
| WAIT TOOL NO. "0" FOR NORMAL | 等待刀具号0表示正常刀具 | |
| WAIT NORMAL NO. NOT FOR BIG TOOL | 等待正常刀具不是大刀 | |
| BIG TOOL'S ADJACENCY NO. NOT "0" | 大刀相邻号不是0 | BC1 |
| BIG TOOL'S ADJACENCY NO. NOT "0" | 大刀相邻号不是0 | BC2 |
| T-CODE EQUAL SPL TOOL NO. FLAG | T代码等于SPL刀具号标志 | |
| T-CODE EQUAL SPL TOOL NO. FLAG 2 | T代码等于SPL刀具号标志2 | |
| BIG TOOL'S ADJACENCY NO. NOT "0" | 大刀相邻号不是0 | BC |
| T-CODE NOT EQUAL SPL TOOL NO. | T代码不等于SPL刀具号 | |
| M06 COMMAND | M6换刀指令 | M06CD |
| ATC STEP 1(TOOL UNCLAMP) | ATC第一步（松开刀具） | ATCS1 |
| ATC STEP 2(TOOL UNCLAMP CHECK) | ATC第二步（刀具松开检查） | ATCS2 |
| ATC STEP 3(TOOL CLAMP) | ATC第三步（夹紧刀具） | ATCS3 |
| ATC STEP 4(ATC HOME CHECK) | ATC第一步（原位检测） | ATCS4 |
| ATC STEP 5(POT UP) | ATC第一步（刀套上） | ATCS5 |
| ATC STEP 6(ATC STEP END) | ATC第一步（结束） | ATCS6 |
| SPINDLE TOOL CL/UNCL STAND BY | 主轴刀具备好 | SPTSBY |
| SPINDLE TOOL CLAMP COMMAND | 主轴刀具夹紧指令 | SPTCLP |
| SPINDLE TOOL UNCLAMP COMMAND | 主轴刀具松开指令 | SPTUNC |
| 1ST TOOL POT DETECT | 1号刀套检测 | 1TPOT |
| TOOL COUNTER RESET COMMAND | 刀具计数器复位指令 | |
| TOOL POT SYNCHRO RESET | 刀套同步复位 | |
| 1ST TOOL POT CHECK FLAG 1 | 1号刀套检测标志1 | |
| 1ST TOOL POT CHECK FLAG 2 | 1号刀套检测标志2 | |
| 1ST TOOL POT CHECK FLAG 3 | 1号刀套检测标志3 | |
| 1ST TOOL POT SYNCHRO ERROR 1 | 1号刀套同步错误1 | |
| TOOL COUNTER EQUAL TO 1 | 刀具计数器等于1 | |
| TOOL POT SYNCHRO ERROR RESET | 刀套同步错误复位 | |
| 1ST TOOL POT SYNCHRO ERROR 2 | 1号刀套同步错误2 | |
| 1ST TOOL POT COUNT ERROR | 1号刀套计数错误 | |
| SPINDLE BIG TOOL | 主轴大刀 | |
| SPINDLE ZERO TOOL | 主轴零号刀具 | |
| TOOL NO. "0" COMMAND FOR BIGTOOL | 刀具编号0指令大刀 | |
| TOOL NO. "0" COMMAND FOR NORMAL | 刀具编号0指令正常刀具 | |
| M06 INITIAL POSITION | M6初始位置 | M06INP |
| MANUAL ATC CHANGER STEP READY | ATC手动准备就绪 | |
| MANUAL ATC CHANGER STEP + AUX. | ATC手动准备+辅助 | |
| MANUAL ATC CHANGER STEP - AUX. | ATC手动准备-辅助 | |
| ATC CHANGER HOME POSITON | ATC原点 | |
| MANUAL ATC CHANGER STEP + | 手动换刀进一步 | |
| MANUAL ATC CHANGER STEP - | 手动换刀退一步 | |
| MANUAL ATC CHANGER STEP+ 1 PULSE | 手动换刀进一步脉冲 | |
| MANUAL ATC CHANGER STEP- 1 PULSE | 手动换刀退一步脉冲 | |
| MANUAL ATC CHANGER STEP OFF | 手动换刀停止 | |
| TOOL NO. DATA CHANGE PROTECT | 刀具编号数据更改保护 | |
| TOOL SEARCH RESULT IS EMPTY | 刀具搜索结果为空 | |
| TOOL SEARCH RESULT BEYOND 1 | 刀具搜索结果超过1 | |
| SPINDLE TOOL NO. SETTING | 主轴刀具编号设置 | |
| M45 CODE FINISH | M45代码完成 | M45FIN |
| TOOL POT ROTATING COMMAND | 刀盘旋转指令 | TPRCD |
| TOOL "0" + DIR SEARCH OK | 刀具0+目录搜索OK | |
| TOOL "0" - DIR SEARCH OK | 刀具0-目录搜索OK | |
| TOOL "0" SEARCH OK | 刀具0搜索OK | |
| TOOL "0" POSITION IS EMPTY | 刀具0位置为空 | |
| TOOL NO.(NOT "0") SEARCH OK | 刀具编号搜索OK | |
| TOOL POT COUNTER PULSE | 刀套计数脉冲 | |
| T-CODE COMMAND FINISH | T代码完成 | |
| T-CODE COMMAND FINISH FLAG 1 | T代码完成标志1 | |
| T-CODE COMMAND FINISH FLAG 2 | T代码完成标志2 | |
| T-CODE STEP FINISH | T代码单步完成 | |
| BIG TOOL CHANGE P SEARCH STOP | 大刀更换P搜索停止 | |
| ATC ALARM CANCEL | ATC报警取消 | |
| TOOL POT RATTION CONDITION | 刀套旋转条件 | |
| M6 5-STEP FLAG | M6五步标志 | |
| M6 STEP1: TOOL CHANGEABLE JUDGE | M6步骤1：刀具更换判断 | |
| M6 STEP2: DATA READ FINISH | M6步骤2：数据读取完成 | |
| M6 STEP3: TOOL CHANGEABLE | M6步骤3：可更换刀具 | |
| M6 STEP4: TOOL CHANGE(1 STEP) | M6步骤4：换刀 | |
| M6 STEP5: WAITING-P UP CONFIRM | M6步骤5：大刀刀套向上确认 | |
| M6 STEP3.0 TOOL NOT CHANGEABLE | M6步骤3.0：刀具不可更换 | |
| M6 STEP3.1 MAGAZINE STOP | M6步骤3.1：刀库停止 | |
| M6 STEP3.2 MAGAZINE STOP CONFIRM | M6步骤3.2：刀库停止确认 | |
| M6 STEP3.3 BIG T CHANGE P SEARCH | M6步骤3.3：大刀刀套搜索 | |
| M6 STEP3.4 WAITING POT DOWN | M6步骤3.4：等待刀套倒下 | |
| M6 STEP3.5 TOOL TEMPORARY CHANGE | M6步骤3.5：刀具临时更换 | |
| M6 STEP3.6 WAITING-P UP CONFIRM | M6步骤3.6：等待刀套抬起确认 | |
| M6 STEP3.7 NORMAL TOOL SEARCH | M6步骤3.7： | |
| M6 STEP3.8 WAITING POT DOWN | M6步骤3.8： | |
| M6 STEP3.9 TOOL CHANGE | M6步骤3.9： | |
| M6 STEP3.10 WAITING-P UP CONFIRM | M6步骤3.10： | |
| ATC ALARM | ATC报警 | |
| M233 FLAG | M233标志 | |
| ATC CHANGE START FLAG | 换刀开始标志 | |
| M233 CODE FINISH | M233完成 | |
| M232 CODE FINISH | M232完成 | |
| M06 CODE FINISH | M06完成 | |
| M06 COMMAND STEP FINISH | M06单步完成 | |
| MAGAZINE POT COUNT 2 CONDITION | 刀套计数2条件 | |
| TOOL COUNTER 2 AUX | 刀具计数2辅助 | |
| TOOL NO COUNT 2 ERROR | 刀具无计数2错误 | |
| TOOL COUNTER 1 EQUAL TO 2 | 刀具计数1等于2 | |
| 1ST TOOL POT CHECK DELAY | 1号刀套检查延时 | |
| MAGAZINE POT COUNT 2 AUX | 刀套计数2辅助 | |
| MAGAZINE DIRECTION MEMORY | 刀套号存储器 | |
| PLC READY CONDITION | PLC就绪状态 | PRC |
| MACHINE READY AUX | 机器就绪辅助 | MRYA |
| HYDRAULIC UNIT PRESSURE OK | 液压站压力正常 | HPOK |
| ALL LED LAMPS FLICKING | 所有LED灯闪烁 | ALF |
| SPDL & COOLANT OFF IN SP | SPCLOFF | |
| M02/M30 HOLD | M02/03保持 | M32H |
| SINGLE BLOCK MODE PULSE | 单步模式脉冲 | SBKP |
| OPTIONAL BLOCK SKIP MODE PULSE | 可选块跳过模式脉冲 | BDTP |
| OPTIONAL STOP MODE PULSE | 可选块停止模式脉冲 | OPSP |
| DRY RUN MODE PULSE | 空运行模式脉冲 | DRNP |
| MST MODE PULSE | MST模式脉冲 | MSTP |
| PROGRAM RESTART MODE PULSE | 程序重启模式脉冲 | PRSP |
| ALL AXES MACHINE LOCK PULSE | 全轴锁定模式脉冲 | AALP |
| Z AIXS MACHINE LOCK PULSE | Z轴锁定模式脉冲 | ZALP |
| AUTO POWER OFF PULSE | 自动断电脉冲 | APOP |
| OPTIONAL STOP MODE ON | 可选停止模式打开 | OPSM |
| M00/M01 FINISH | M00/01完成 | OPSMFIN |
| ALL AXES MACHINE LOCK | 全轴锁定 | AAML |
| Z AXIS MACHINE LOCK | Z轴锁定 | ZAML |
| M02/30 HOLD AUX | M02/30保持辅助 | M32A |
| AUTO POWER OFF MODE ON | 自动断电模式打开 | APOM |
| AUTO POWER OFF | 自动断电 | APO |
| 4,5 AXIS SELECT | 4-5轴选择 | 4,5AS |
| X AXIS REF. RETURN COM | X轴参考点返回 | XRRC |
| Y AXIS REF. RETURN COM | Y轴参考点返回 | YRRC |
| Z AXIS REF. RETURN COM | Z轴参考点返回 | ZRRC |
| 4 AXIS REF. RETURN COM | 4轴参考点返回 | 4RRC |
| 5 AXIS REF. RETURN COM | 5轴参考点返回 | 5RRC |
| OVERRIDE CANCEL | 超程取消 | |
| M48,M49 FINISH | M48/49完成 | M489FIN |
| CUTTING MODE SP SPEED 0 VALID | 切削模式主轴速度0有效 | CMSS0V |
| M184/M185 CODE FINISH | M1845FIN | |
| SPINDLE ORIENTATION RESTART | 主轴定向重启 | SOR |
| WORK LIGHT ON PULSE | 工作灯开启脉冲 | WLP |
| COOLANT OFF | 冷却关闭 | COLOF |
| FLOOD COOLANT ON | 冷却液开启 | FCOL |
| FLOOD COOLANT MANUAL ON PULSE | 冷却液手动开启脉冲 | FCOLOP |
| COOLANT MANUAL OFF PULSE | 冷却手动关闭脉冲 | FCOLOFP |
| FLOOD COOLANT MANUAL ON AUX | 冷却液手动开启辅助 | FCOLOA |
| FLOOD COOLANT MANUAL OFF AUX | 冷却液手动关闭辅助 | FCOLOFA |
| COOLANT TEMPERARY OFF | 冷却液温度关闭 | COLTOFF |
| INITIAL LUBRICATION | 初始润滑 | ILUB |
| NO MOVEMENT IN ALL AXES | 全轴静止 | NOMV |
| LUBRICATION STOP AFTER 1H NO MOV | 1H无运动后停止润滑 | LST |
| PATROL LIGHT RD | 红灯 | RD |
| PATROL LIGHT YELLOW | 黄灯 | YW |
| PATROL LIGHT GREEN | 绿灯 | GN |
| PATROL LIGHT RED & YELLOW | 红、黄灯 | RDYW |
| PATROL LIGHT YELLOW & GREEN | 黄、绿灯 | YWGN |
| PATROL LIGHT RED & GREEN | 红、绿灯 | RDGN |
| PATROL LIGHT RED & YELLOW &GREEN | 红、黄、绿灯 | RDYWGN |
| MACHINE ALARM STATUS | 机器报警状态 | MAS |
| PROGRAM END & PROGRAM STOP | 程序结束、停止 | 32LOSL |
| AXIS STOP CONDITION | 轴停止条件 | ASC |
| MACHINE STOP CONDITION | 机器停止状态 | MSC |
| FRONT DOOR OPEN ENABLE | 前门打开启用 | FDOE |
| FRONT DOOR OPEN CHECK FLAG | 前门打开检查标志 | FDOCHK |
| FRONT DOOR UNLOCK RELEASE | 前门解锁释放 | FDULR |
| FRONT DOOR UNLOCK BY M02/30 | 前门解锁M02/30 | FDULM |
| FRONT DOOR UNLOCK COMMAND | 前门解锁指令 | FDULC |
| COLLET AIR BLOW ON | 夹头吹气 | CAIR |
| COLLET AIR M-CODE FINISH | 夹头吹气代码完成 | M145FIN |
| FLOOD COOLANT M-CODE FINISH | 冷却液手动代码完成 | M89FIN |
| FLOOD COOLANT MANUAL ON KEEP | 冷却液手动保持 | FCOK |
| COOLANT MANUAL OFF KEEP | 手动冷却关闭 | COFK |
| SHOWER COOLANT ON | 喷淋开启 | SCOLO |
| SHOWER COOLANT ON AUX | 喷淋开启 | SCOLOA |
| SHOWER COOLANT MANUAL ON PULSE | 喷淋手动开启脉冲 | SCMOP |
| SHOWER COOLANT MANUAL ON KEEP | 喷淋手动开启 | SCMOK |
| SHOWER COOLANT MANUAL ON AUX | 喷淋手动开启 | SCMOA |
| PROGRAM REPEAT AUX | 程序重复 | PRA |
| PROGRAM REPEAT ON | 程序重复 | PRO |
| PARTS COUNT AND PROGRAM REPEAT F | 零件计数和程序重复 | M545FIN |
| MIRROR IMAGE M-CODE FINISH | 镜像代码完成 | MIRFIN |
| OPTIONAL STOP 1 | 可选停止1 | OPS1 |
| OPTIONAL STOP 2 | 可选停止2 | OPS2 |
| MF STROBE 1 PULSE AUX | MF选通脉冲1 | MFSPA |
| G00 MODE | G00模式 | |
| INITIAL 1 PULSE AUX | 初始1脉冲 | INPA |
| THROUGH SPINDLE COOLANT | 主轴冷却 | TCOL |
| THROUGH SPINDLE COOLANT AUX | 主轴冷却 | TCOLA |
| TSC MANUAL ON PULSE | TSC手动脉冲 | TSCOP |
| TSC MANUAL ON KEEP | TSC手动保持 | TSCOK |
| TSC MANUAL ON AUX | TSC手动 | TSCOA |
| EXTERNAL M-CODE FINISH | 外部代码完成 | EMEN |
| WORKPIECE MEASUREMENT ON FLAG | 工件测量打开标志 | WMOF |
| WORKPIECE MEASUREMENT SENSOR ON | 工件测量传感器打开 | WMSO |
| TOOL MEASUREMENT ON FLAG | 刀具测量打开标志 | TMOF |
| TOOL MEASUREMENT SENSOR ON | 刀具测量传感器打开 | TMSO |
| TOOL MEASURE LATCH MODE (NCi-5) | 刀具测量锁定模式 | TMLM |
| MEASURE SYSTEM OFF FLAG | 测量系统关闭标志 | MSOFF |
| MEASURE SYSTEM OFF M-CODE FINISH | 测量系统关闭代码完成 | M73FIN |
| CHIP CONVEYOR RUN WHEN STL | 排屑器在STL时运行 | CCRSTL |
| CHIP CONVEYOR RUN BY M24 AND MAN | 排屑器在手动和M24运行 | CCRM24 |
| CHIP CONVEYOR SWITCH PULSE | 排屑器开关脉冲 | CCSP |
| CHIP CONVEYOR MANUAL OFF | 排屑器手动关闭 | CCMOFF |
| CHIP CONVEYOR MANUAL ON | 排屑器手动开启 | CCMON |
| AIR BLOW ON AUX | 吹气 | ABOA |
| AIR BLOW M-CODE FINISH | 吹气代码完成 | M145FIN |
| AIR BLOW SWITCH PULSE | 吹气开关脉冲 | ALSP |
| AIR BLOW MANUAL OFF | 吹气手动关 | ALMOFF |
| AIR BLOW MANUAL ON | 吹气手动开 | ALMON |
| OIL MIST ON AUX | 油雾开 | OMOA |
| OIL MIST M-CODE FINISH | 油雾开代码完成 | M1323FIN |
| OIL MIST SWITCH PULSE | 油雾开关脉冲 | OMSP |
| OIL MIST MANUAL OFF | 油雾手动关 | OMMOFF |
| OIL MIST MANUAL ON | 油雾手动开 | OMMON |
| COOLANT GUN SWITCH PULSE | 水枪开关脉冲 | CGSP |
| AUTO DOOR OPEN COMMAND | 自动门打开指令 | ADOC |
| AUTO DOOR CLOSE COMMAND | 自动关闭指令 | ADCC |
| AUTO DOOR OPEN KEEP | 自动门打开保持 | ADOK |
| AUTO DOOR CLOSE KEEP | 自动门关闭保持 | ADCK |
| AUTO DOOR INTERRUPT RESET | 自动门中断复位 | ADIR |
| AUTO DOOR INTERRUPTION | 自动门中断 | ADINT |
| AUTO DOOR SOFT START & STOP END | 自动门软启停结束 | ADSSSE |
| AUTO DOOR M-CODE FINISH | 自动门代码完成 | M523FIN |
| 4 AXIS CLAMP AUX | 4轴夹紧 | 4ACA |
| 4 AXIS UNCLAMP AUX | 4轴松开 | 4AUCA |
| 4 AXIS SERVO OFF | 4轴伺服关闭 | 4ASOFF |
| 4 AXIS M-CODE FINISH | 4轴代码完成 | M101FIN |
| FIXTURE 1 SELECTED | 已选择夹具1 | F1S |
| FIXTURE 2 SELECTED | 已选择夹具2 | F2S |
| FIXTURE 3 SELECTED | 已选择夹具3 | F3S |
| FIXTURE 4 SELECTED | 已选择夹具4 | F4S |
| FIXTURE 1 MANUAL CLAMP | 夹具1夹紧 | F1MC |
| FIXTURE 1 MANUAL UNCLAMP | 夹具1放松 | F1MUN |
| FIXTURE 2 MANUAL CLAMP | 夹具2夹紧 | F2MC |
| FIXTURE 2 MANUAL UNCLAMP | 夹具2放松 | F2MUN |
| FIXTURE 3 MANUAL CLAMP | 夹具3夹紧 | F3MC |
| FIXTURE 3 MANUAL UNCLAMP | 夹具3放松 | F3MUN |
| FIXTURE 4 MANUAL CLAMP | 夹具4夹紧 | F4MC |
| FIXTURE 4 MANUAL UNCLAMP | 夹具4放松 | F4MUN |
| FIXTURE M-CODE FINISH | 夹具代码完成 | FIXFIN |
| FIXTURE 1 CLAMPED | 夹具1夹紧 | F1C |
| FIXTURE 2 CLAMPED | 夹具2夹紧 | F2C |
| FIXTURE 3 CLAMPED | 夹具3夹紧 | F3C |
| FIXTURE 4 CLAMPED | 夹具4夹紧 | F4C |
| (B)EMERGENCY ALARM | 急停 | B.E-ALM |
| (B)CYCLE STOP ALARM | 循环停止报警 | B.C-ALM |
| (B)SINGLE BLOCK ALARM | 单步报警 | B.S-ALM |
| (B)MESSAGE ALARM | 信息报警 | B.M-ALM |
| LOGIC ON | 逻辑开启 | A |
| (B)AXIS INTERLOCK | 轴连锁 | B.IT |
| (B)HOME POSITON INTERLOCK | 原点连锁 | HOMINT |
| (B)DOOR INTERLOCK | 门连锁 | DINON |
| (B)ATC INTERLOCK | ATC连锁 | ATCINT |
| 4 AXIS INTERLOCK | 4轴连锁 | 4INT |
| FIXTURE CLAMP STATE | 夹具夹具状态 | FCS |
| INITIAL 1 PULSE | 初始1脉冲 | 1PULSE |
| MANUAL MODE | 手动模式 | MAN |
| AUTO MODE | 自动模式 | AUT |
| OPTIONAL STOP | 可选停止 | OPS |
| M FUNCTION FINISH | M指令完成 | MFIN |
| S FUNCTION FINISH | S指令完成 | SFIN |
| T FUNCTION FINISH | T指令完成 | TFIN |
| DOOR CLOSE STATE | 门关闭状态 | DCL |
| FEEDRATE OVERRIDE 0% | 进给速率0% | F0% |
| SPINDLE STOP CONDITION | 主轴停止状态 | SSC |
| ALARM RESET | 报警复位 | ARST |
| AUX. PRESSURE OK FLAG | 压力正常标志 | APOKF |
| SPINDLE TOOL CLAMP STATUS | 主轴刀具夹具状态 | STCS |
| SP MULTI ORENTATION DATA ERROR | 主轴数据错误 | SMORDE |
| OIL COOLING ERROR SPINDLE STOP | 油冷报警主轴停止 | OCESTP |
| ATC START SENSOR CHECK FLAG | ATC启动传感器检查标志 | ASSCF |
| ATC CLAMP SENSOR SIGNAL ERROR | ATC夹紧传感器信号错误 | ACSSE |
| REF.POINT RETURN INTERLOCK ALARM | 参考点返回连锁错误 | HOMIAL |
| FRONT DOOR SW LOCKING OVER TIME | 前门开关随时间锁定 | FDLKOT |
| FRONT DOOR SW LOCKING ALARM | 前门开关锁定报警 | FDLKAL |
| LUB UNNOMAL PRESSURE ALARM | 润滑压力异常报警 | LUPA |
| LUB ALARM SINGLE BLOCK STOP | 润滑报警单步停止 | LASBS |
| 6401#0 HYDRAULIC UNIT USE | ||
| 6401#1 HYD. UNIT PRESSURE SW USE | ||
| 6401#2 ALL LED LAMPS FLICKING | ||
| 6401#3 (B)INITIAL HOME INTERLOCK | ||
| 6401#4 OPERATION DOOR IGNORE | ||
| 6401#5 DOOR UNLOCK AFTER M02/30 | ||
| 6401#6 WAIT.T-CODE POT DOWN KEEP | ||
| 6401#7 M0/M1 SPDL & COOLANT OFF | ||
| 6402#0 SPDL & COOLANT OFF IN SP | ||
| 6402#1 FEEDRATE CLAMPED TO 100% | ||
| 6402#2 SP OVR CLAMPED TO 100% | ||
| 6402#3 SPINDLE SPEED CONFIRM USE | ||
| 6402#4 SP MULTI-ORIENTATION USE | ||
| 6402#5 M00/01->SINGLE BLOCK | ||
| 6402#6 AIR PRES. NOT USE | ||
| 6402#7 OIL COOLING UNIT USE | ||
| 6403#0 FIXTURE USE | ||
| 6403#1 ATC USE | ||
| 6403#2 20TOOLS ATC USE | ||
| 6403#3 24TOOLS ATC USE | ||
| 6403#4 SPDL CL/UC MANUAL IN OPS | ||
| 6403#5 ATC 2ND REF. POINT USE | ||
| 6403#6 T = SP TOOL NO ALARM USE | ||
| 6404#0 4TH AXIS USE | ||
| 6404#1 5TH AXIS USE | ||
| 6404#2 4 AXIS CLAMP WHEN SOL. ON | ||
| 6404#3 4 AXIS SERVO OFF USE | ||
| 6404#4 4 AXIS AUTO CLAMP/UN USE | ||
| 6404#5 4 AXIS CONTROL BY AIR | ||
| 6404#6 M-C0DE OVERTIME USE | ||
| 6405#0 TAPPING RETRACT USE | ||
| 6405#1 1AB FIXTURE USE | ||
| 6405#2 2AB FIXTURE USE | ||
| 6405#3 3AB FIXTURE USE | ||
| 6405#4 4AB FIXTURE USE | ||
| 6405#5 FIX. CONTROLED BY ONE M | ||
| 6405#6 FIXTURE PRESSURE CHECK | ||
| 6405#7 FIXTURE AIR SENSING USE | ||
| 6406#0 COOLANT ON SW ALAWYS USE | ||
| 6406#1 COOLANT KEEP IN DOOR OPEN | ||
| 6406#2 COLLET AIR ON WHEN MAN SP | ||
| 6406#3 COLLET AIR ON WHEN T CODE | ||
| 6406#4 TOOL COUNTER 2 NOT USE | ||
| 6407#0 PATROL LIGHT RED USE | ||
| 6407#1 PATROL LIGHT YELLOW USE | ||
| 6407#2 PATROL LIGHT GREEN USE | ||
| 6408#0 AUTO POWER OFF USE | ||
| 6408#1 CLNT GUN ON WHEN D OPEN | ||
| 6408#2 CLNT OFF USE FOR TSC | ||
| 6408#3 CLNT TANK LOW LEVEL CHECK | ||
| 6408#4 TSC FILTER NOT CHECK | ||
| 6408#5 CLNT OFF USE FOR SHOWER | ||
| 6409#0 OIL MIST COLLECTOR USE | ||
| 6409#1 COOLANT GUN USE | ||
| 6409#2 AIR BLOW USE | ||
| 6409#3 TSC USE | ||
| 6409#4 FLUSHING/SHOWER CLNT USE | ||
| 6409#5 CHIP CONVEYOR USE | ||
| 6409#6 CHIP CONVEYOR ON WHEN STL | ||
| 6410#0 EXTERNAL M-CODE USE | ||
| 6410#1 WORKPIECE MEASUREMENT USE | ||
| 6410#2 TOOL MEASUREMENT USE | ||
| 6410#3 AUTO DOOR USE | ||
| 6410#4 AUTO D SAFTY DEVICE USE | ||
| 6411#0 NC WORK COUNTER USE | ||
| 6411#1 EXTERNAL WC & TC USE |
共享屋微信：136959805
