以下中文由电脑翻译，仅供参考，英文原版请见后半部分。
AIC 代码 – 接收来自相关操作控制的信号
AIC 523671.02 — 驱动杆电路冲突
代码由以下原因引起：右侧反向器位置的正向槽错误。
控制单元响应：默认为中性
AIC 523671.07 — 驱动杆调整故障
代码由以下原因引起：机械系统无响应或调整不足。
控制单元响应：控制杆不在 PARK 中
AIC 523671.11 — 换档装置（DirectDrive 变速器），故障
无法确定换档杆位置。
控制软件的反应：变速器功能有限或没有。
AIC 523671.13 — AIC 校准错误/未校准
代码，原因如下：变速杆的校准超出最大范围，或保存了失败的校准。
控制单元响应：命令 PARK
AIC 523745.02 — 用于 iTEC™ 程序选择的开关，故障
在用于 iTEC™ 程序选择的开关处检测到不正确的开关逻辑（序列 1 和 2）。这可能表示开关或电路有故障。
控制软件的反应：iTEC™ 程序选择开关的功能有限或没有功能。
AIC 523745.03 — 用于 iTEC™ 程序选择的开关，电压过高
用于 iTEC™ 程序选择的开关电压过高。这可能是由于开关故障或短路而发生的。
控制软件的反应：iTEC™ 程序选择开关的功能有限或没有功能。
AIC 523745.04 — 用于 iTEC™ 程序选择的开关，电压太低
用于 iTEC™ 程序选择的开关电压太低。这可能是由于开关故障或短路而发生的。
控制软件的反应：iTEC™ 程序选择开关的功能有限或没有功能。
AIC 523745.11 — iTEC™ 程序选择开关、iTEC™ 程序选择故障
开关按下时间过长。这可能表示开关卡住或脏污。
控制软件的反应：iTEC™ 程序选择开关的功能有限或没有功能。
AIC 523775.02 — 多功能杠杆式在线状态开关电路故障
代码由以下原因引起：多功能杠杆式在线状态开关输出冲突。
控制单元响应：功能禁用 （OFF）
AIC 523776.02 — 多功能杠杆运输锁开关电路故障
代码由以下原因引起：多功能杠杆运输锁开关输出冲突。
控制单元响应：功能禁用 （OFF）
AIC 523804.02 — 多功能杠杆横向定位开关电路故障
代码由以下原因引起：多功能杠杆横向定位开关故障。
控制单元响应：功能禁用 （OFF）
AIC 523804.03 — 多功能杠杆横向传感器电路电压高
代码 原因：多功能杠杆横向传感器电压高于 4.80 V.
控制单元响应：功能禁用 （OFF）
AIC 523804.04 — 多功能杆，左右轴，电压过低
多功能杆左右轴电压过低或短路。
控制软件的反应：多功能杆功能受限或无功能。
AIC 523805.02 — 多功能杆，前后轴，信号超出范围
接收到的电压与多功能杆的开关位置不匹配。
控制软件的反应：多功能杆功能受限或无功能。
AIC 523805.03 — 多功能杆 （E-ICV），前后轴，电压过高
多功能杆前后轴电压过高或短路。
控制软件的反应：多功能杆功能受限或无功能。
AIC 523805.04 — 多功能杆，前后轴，电压过低
多功能杆前后轴的电压过低或短路。
控制软件的反应：多功能杆功能受限或无功能。
AIC 523923.02 — SCV I 控制杆开关/传感器冲突
代码由以下原因引起：SCV I 控制杆擒动开关与传感器电压冲突。E-SCV I 控制杆的电位器信号电压超出范围或控制杆开关的状态与电位器信号电压不匹配。
控制单元响应：SCV I 已禁用
AIC 523923.03 — E-SCV I 控制杆，电压过高
E-SCV I
控制杆电压过高或短路控制软件的反应：E-SCV I 控制杆功能受限或没有功能。
AIC 523923.04 — E-SCV I 控制杆、电压过低
、电压过低或 E-SCV I
控制杆短路。控制软件的反应：E-SCV I 控制杆功能受限或没有功能。
AIC 523953.02 — 速度控制杆传感器电路冲突
代码由以下原因引起：速度控制杆传感器电压 1 和 2 冲突。通道 1 和通道 2 之间速度控制杆传感器单元的电压比不正确。这可能是由电路故障引起的。
控制单元响应：命令 PARK
AIC 523953.03 — 速度控制杆传感器电压高
AIC codes – receives the signals from the relevant operating controls
AIC 523671.02 — Drive Lever Circuit
Conflict
Code caused by: Forward slot of right-hand reverser position error.
Control Unit Response: Defaults to Neutral
AIC 523671.07 — Drive Lever Adjustment
Fault
Code caused by: Mechanical system not responding or out of adjustment.
Control Unit Response: Lever Not In PARK
AIC 523671.11 — Shift Unit (DirectDrive
Transmission), Fault
The shift lever position cannot be determined.
Reaction of the control software: Limited or no function of the transmission.
AIC 523671.13 — AIC Calibration
Fault/Not Calibrated
Code caused by: Calibration for shift lever is outside maximum range, or a
failed calibration was saved.
Control Unit Response: Commands PARK
AIC 523745.02 — Switch for iTEC™ Program
Selection, Fault
Incorrect switch logic detected at the switch for iTEC™ program selection
(sequences 1 and 2). This may indicate a faulty switch or circuit.
Reaction of the control software: Limited or no function of the iTEC™ program
selection switch.
AIC 523745.03 — Switch for iTEC™ Program
Selection, Voltage Too High
Voltage of switch for iTEC™ program selection too high. This may occur as a
result of a faulty switch or a short circuit.
Reaction of the control software: Limited or no function of the iTEC™ program
selection switch.
AIC 523745.04 — Switch for iTEC™ Program
Selection, Voltage Too Low
Voltage of switch for iTEC™ program selection too low. This may occur as a
result of a faulty switch or a short circuit.
Reaction of the control software: Limited or no function of the iTEC™ program
selection switch.
AIC 523745.11 — Switch for iTEC™ Program
Selection, Fault
Switch for iTEC™ program selection pressed too long. This may indicate that the
switch is stuck or dirty.
Reaction of the control software: Limited or no function of the iTEC™ program
selection switch.
AIC 523775.02 — Multi-Function Lever
Hand Presence Switch Circuit Fault
Code Caused By: Multi-Function lever presence switch outputs conflicting.
Control Unit Response: Function Disabled (OFF)
AIC 523776.02 — Multi-Function Lever
Transport Lock Switch Circuit Fault
Code Caused By: Multi-Function lever transport lock switch outputs conflicting.
Control Unit Response: Function Disabled (OFF)
AIC 523804.02 — Multi-Function Lever
Lateral Detent Switch Circuit Fault
Code Caused By: Multi-Function lever lateral detent switch fault.
Control Unit Response: Function Disabled (OFF)
AIC 523804.03 — Multi-Function Lever
Lateral Sensor Circuit Voltage High
Code Caused By: Multi-Function lever lateral sensor voltage higher than 4.80 V.
Control Unit Response: Function Disabled (OFF)
AIC 523804.04 — Multi-Function Lever,
Left-Right Axis, Voltage Too Low
Voltage too low or shorted circuit at the left-right axis of the multi-function
lever.
Reaction of the control software: Limited or no function of the multi-function
lever.
AIC 523805.02 — Multi-Function Lever,
Fore-Aft Axis, Signal Out of Range
The voltage received does not match the switch position of the multi-function
lever.
Reaction of the control software: Limited or no function of the multi-function
lever.
AIC 523805.03 — Multi-Function Lever
(E-ICV), Fore-Aft Axis, Voltage Too High
Voltage too high or shorted circuit at the fore-aft axis of the multi-function
lever.
Reaction of the control software: Limited or no function of the multi-function
lever.
AIC 523805.04 — Multi-Function Lever,
Fore-Aft Axis, Voltage Too Low
Voltage too low or shorted circuit at the fore-aft axis of the multi-function
lever.
Reaction of the control software: Limited or no function of the multi-function
lever.
AIC 523923.02 — SCV I Control Lever
Switch/Sensor Conflict
Code Caused By: SCV I Control Lever detent switch conflicts with sensor
voltage. Potentiometer signal voltage of E-SCV I control lever is out of range
or status of control lever switch and potentiometer signal voltage do not
match.
Control Unit Response: SCV I disabled
AIC 523923.03 — Control Lever for E-SCV
I, Voltage Too High
Voltage too high or shorted circuit at the control lever for E-SCV I.
Reaction of the control software: Limited or no function of control lever for
E-SCV I.
AIC 523923.04 — Control Lever for E-SCV
I, Voltage Too Low
Voltage too low or shorted circuit at the control lever for E-SCV I.
Reaction of the control software: Limited or no function of control lever for
E-SCV I.
AIC 523953.02 — Speed Control Lever
Sensor Circuit Conflict
Code Caused By: Speed Control Lever Sensor voltages 1 and 2 conflict. The
voltage ratio at the speed control lever sensor unit between channel 1 and
channel 2 is not correct. This may be caused by a faulty circuit.
Control Unit Response: Commands PARK
