超级终端显示如下：
Reset cause: POR
Board: Edge10
DRAM: 512 MiB
MMC: FSL_SDHC: 0
Using default environment
In: serial
Out: serial
Err: serial
HAB Configuration: CLOSED
HAB State: TRUSTED
No HAB Events Found. System booted cleanly.
CPU ID = D85B99EAD4692C0D
Restore button press detected. Please release button to initiate factory restore
.
Restore mode is set!
Net: FEC [PRIME]
Hit any key to stop autoboot: 0
Loading QNX IFS...
Checking boot plan
reading n4-edge10.f1img
Loaded
Decrypting...
Validating...
OK
## Starting application at 0x80100000 ...
MMFLAGS=1
*******************************************************************************
*******************************************************************************
MAINTENANCE BUILD
Build Version: 2018.8.29
built on 2018-08-29 20:30:18
*******************************************************************************
*******************************************************************************
Starting watchdog...
Starting random service ...
Starting serial devices ...
Starting gpio...
Starting I2C1,2,3,4 driver (/dev/i2c1,2,3,4)...
Starting rtc utility...
Starting spi driver (/dev/spi)...
Maintenance image started
Starting eMMMC driver
uda enhanced setting already set 1!
Path=0 - imx6
target=0 lun=0 Direct-Access(0) - SDMMC: 004G60 Rev: 0.2
Mount boot partition...
Mount recovery partition...
Launching 'recovery' action...
Starting recovery...
Verifying recovery image...
Creating RAM disk...
Verifying recovery image, this will take a minute...
n4-edge10-factory-fs.tgz
n4-edge10.f1img
Formatting QNX6 file system...
Restoring factory defaults...
/mnt/fs/: -snapshot
Restoring factory file system /mnt/maint/n4-edge10-factory-fs.tgz...
Restoring default licenses...
Restoring factory OS image /mnt/maint/n4-edge10.f1img...
/mnt/fs/: +snapshot
Completed recovery.
U-Boot 2016.03-E10-1.0.4 (Sep 13 2018 - 10:46:37 -0400)
CPU: Freescale i.MX6SX rev1.3 at 792MHz
CPU: Industrial temperature grade (-40C to 105C) at 50C
Reset cause: WDOG
Board: Edge10
DRAM: 512 MiB
MMC: FSL_SDHC: 0
Using default environment
In: serial
Out: serial
Err: serial
HAB Configuration: CLOSED
HAB State: TRUSTED
No HAB Events Found. System booted cleanly.
CPU ID = D85B99EAD46
Net: FEC [PRIME]
Hit any key to stop autoboot: 0
Loading QNX IFS...
Checking boot plan
reading n4-edge10.f1img
Loaded
Decrypting...
Validating...
OK
## Starting application at 0x80100000 ...
MMFLAGS=1
Welcome to QNX Neutrino 7.0 on the NXP i.MX6 SoloX SDB (ARM Cortex A9/M4 Platfor
m)
Starting watchdog...
Starting random service ...
Starting serial devices ...
Path=0 - imx6
target=0 lun=0 Direct-Access(0) - SDMMC: 004G60 Rev: 0.2
Checking QNX6 power safe filesystem...
Started QNX6 power safe filesystem
Checking FAT32 filesystem...
Started FAT32 Type-x0C filesystem...
no fsencrypt domain created, create it
OK
encrypt /home/niagara
encrypt /etc
encrypt /var
Starting spi driver...
Starting edgeGpio...
starting I2C driver...
Starting RTC driver
Restoring maintenance logs...
Missing user files, restoring factory defaults
uid:400
Username/password reset to factory defaults.
Missing network configuration file, restoring factory defaults
NOTICE: Missing JRE Time Zone file '/etc/timezone', setting to UTC
Missing link configuration file, restoring factory defaults
Press ESC to choose alternate boot options...
continuing boot...
Starting HSM resource-manager...
launching qspyd2...
Append Niagara settings to dhclient configuration file
eth_conf: Working in Daisy Chain mode (RSTP disabled).
Configuring en0...
Requesting an IP address via DHCP for adapter en0...
if_up: retries exhausted
NOTICE: en0 adapter configuration failed
----------------------TCP/IP Network Status------------------------------
en0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
address: 00:01:f0:08:
media: Ethernet autoselect (none)
status: no carrier
inet6 fe80::201:f0ff:fe 6%en0 prefixlen 64 scopeid 0x11
-------------------------------------------------------------------------
pf enabled
ssh-keygen: generating new host keys:
calling bnbpf with en
Starting BACnet resource manager
Station rename: Renamed station Edge10 as Edge10
INFO [2019-07-03 15:26:17][nverify] Verifying archive /opt/niagara/bin
INFO [2019-07-03 15:26:19][nverify] Verifying archive /opt/niagara/jre
niagarad_init: Integrity validation success. Continuing niagarad startup.
niagarad_init: creating mqueue /niagarad-to-os
niagarad_init: creating mqueue /os-to-niagarad
updating /etc/config/ttys
updating /etc/shells
login:
